- How to factory reset hp jetdirect 170x manuals#
- How to factory reset hp jetdirect 170x install#
- How to factory reset hp jetdirect 170x manual#
To obtain technical help, try Contact hp for technical help. Please note this form isįor feedback only, so you will not receive a response. If you selected not easy for question 2, in which section did you expect to find it?įeedback will be used to improve our content. How does the information on this page help you?ģ. To help us improve our content, please provide your feedback below.ġ. Power cord while continuing to hold down the TEST button for five to 30 Reset the HP Jetdirect external print server: disconnect the powerĬord, hold down the TEST button on the print server, then connect the Novell or IPX/SPX settings should read Not Configured, DLC/LLC should read Ready. The default TCP/IP address is 192.0.0.192. After resetting the printer server, you will Resetting the print server will reset all settings Hold the TEST button until the Status LED is. Release the test button at the right LED pattern and the configuration Afterwards the LEDs begin to cycle through fourĬonfigurations for the PDLs, as outlined in the following table.
When holding down the test button, (located between the StatusĪnd Activity LEDs) the Status and Activity LEDs will be on and solidįor about 3-4 seconds. LEDs and TEST button are used to select a PDL for the configuration PCL, the Page Description Language (PDL) can be changed to either PCL,
How to factory reset hp jetdirect 170x manuals#
Refer to thisĬonfiguration page when configuring the software.Ĭonfigure the EX Plus or EX Plus3 by referring to the corresponding chapter for the network in the HP Jetdirect Family of Print Servers Software Installation Guide.Ĭlick here to download manuals for the Jetdirect print serversĬonfiguration page for the EX Plus or EX Plus3 print server is sent to Hardware installation has been successfully completed. If the configuration page displays the message I/O Card Ready, the Print a configuration page by pressing and releasing the TEST button on the print server. To print a configuration page, follow these steps: PCL, please refer to the next section for selecting the appropriate If the printer attached to Port 1 does not support HP This page is printed from Port 1 of the print server and is in HP Verify the installation of the print server, print a configuration Troubleshooting chapter of the HP Jetdirect Family of Print Servers Software Installation Guide that came with the Jetdirect. If the problem cannot be corrected, check the If the internal self-test fails, the Activity LED will be on and the The Status LED should be green (it may be steady or it may be blinking). Since there is no power switch, the print server is on after plugging it in.Ĭheck the LEDs on the print server. Plug the power module into the wall outlet. Plug the power module into the power receptacle in the back of the print server. Printer, it is recommended that attaching that printer to Port 1.TheĭLC/LLC protocol is supported only on Port 1 of the print server. Plug the network cable into the print server.Ĭonnect the print server to the printer(s). Slide the switch up for 16 Mbit/s or down for 4 Mbit/s.įigure 1 :Back view of Token Ring Jetdirect Ex Plus3 To do this, take a pen or similar object and Switch on the back of the print server to the appropriate speed (4 If there is a Token Ring print server (J2594A), set the data-rate
How to factory reset hp jetdirect 170x manual#
Self-test page (refer to the printer manual for instructions). To ensure the printer(s) work(s) properly, print the printer's demo or
How to factory reset hp jetdirect 170x install#
To install the HP Jetdirect EX Plus and EX Plus3 print servers, complete these steps: Resetting the print server to factory defaults HP Jetdirect EX Plus and EX Plus3 Print Server - Hardware Installation The business support web site, alternatively you can also search across This functionality will enable you to search on
HP Jetdirect EX Plus and EX Plus3 Print Server - Hardware Installation - bpj02590 - HP Business Support Center summary of JavaScript functions on this page
0 kommentar(er)
